Updated Nov 17, 2026· 6 min read

Key takeaways

  • Standard interior double doors with light traffic generally need a dual 600-pound-per-leaf magnetic lock bracket kit, while exterior or high-security double doors should step up to a 1,200-pound-per-leaf rating paired with a listed fire/life-safety release system. A double-door magnetic lock…

Standard interior double doors with light traffic generally need a dual 600-pound-per-leaf magnetic lock bracket kit, while exterior or high-security double doors should step up to a 1,200-pound-per-leaf rating paired with a listed fire/life-safety release system.

A double-door magnetic lock setup uses two electromagnets, one per door leaf, mounted at the header so both doors lock independently but release together when the access control system is triggered. Because these locks are almost always part of a larger access control or fire-safety system, the right choice depends on holding force needed, whether the installation is fire-rated, and what bracket hardware fits the specific door and frame.

Who Should Buy Which Rating

Offices, server rooms, and interior double doors with normal foot traffic are typically well served by a dual-magnet kit rated around 600 pounds of holding force per door leaf, which meets common commercial access control needs without excessive cost. Exterior entrances, high-traffic commercial doors, or doors in locations with higher security requirements generally call for a 1,200-pound-per-leaf rating, which resists more force and is commonly specified for storefronts or secure facility entrances. Any double door that also serves as a fire exit or egress path needs a magnetic lock system integrated with a fire alarm release and a code-compliant request-to-exit mechanism; this is a life-safety requirement, not a preference, and should be confirmed against local fire code and an electrical or security contractor’s guidance before installation.

At a Glance Comparison

Product type Best for Key stated specs Limits
Dual 600 lb magnetic lock kit Interior double doors, offices, light-security areas Makers commonly list 600 lb holding force per leaf, standard header mount bracket Lower holding force not ideal for exterior or forced-entry-prone locations
Dual 1,200 lb magnetic lock kit Exterior doors, higher-security entrances Makers commonly list 1,200 lb holding force per leaf, reinforced bracket hardware Higher current draw; needs adequately rated power supply
Z-bracket or L-bracket kits for outswing doors Doors that open outward or have narrow frame profiles Makers list bracket geometry designed to offset the magnet from a narrow frame Must match the door’s specific swing direction and frame width
Fail-safe fire-rated release kits Fire exits, egress doors, code-required installations Makers list compatibility with fire alarm panels and request-to-exit devices, fail-safe (unlocks on power loss) operation Requires integration with the building’s existing fire and access control systems

Fit and Compatibility Notes

Standard magnetic lock brackets mount to the door header and the top edge of the door leaf, so frame depth, header material, and whether the door is inswing or outswing all affect which bracket style fits. Doors without a flat, sufficiently deep header may need a specialized L- or Z-bracket to properly offset the magnet and armature plate. Door leaf material matters too: solid wood and metal doors generally accept standard mounting hardware, while glass or narrow-stile aluminum doors often need a dedicated glass-door bracket kit designed for that application.

Fail-Safe vs. Fail-Secure

Magnetic locks are inherently fail-safe, meaning they unlock automatically when power is cut, which is a key reason they’re commonly chosen for doors along a fire egress path. This is different from fail-secure electric strikes or electrified locksets, which stay locked on power loss; mixing lock types on related doors without understanding this distinction can create a code violation or safety issue.

Pick X If… Decision Table

If your door is… Pick this type
Interior, light traffic, standard security Dual 600 lb kit
Exterior, high traffic, or higher security need Dual 1,200 lb kit
Outswing or has a narrow header/frame Z-bracket or L-bracket kit matched to the door profile
Part of a fire exit or egress path Fail-safe kit integrated with fire alarm release, confirmed against local code
Glass or narrow-stile aluminum construction Glass-door specific mounting bracket kit

Installation and Code Notes

Magnetic locks on doors used for emergency egress are subject to fire and building code requirements in most jurisdictions, generally requiring a request-to-exit sensor, a fire alarm interface that releases the lock on alarm activation, and sometimes a manual pull station near the door. These requirements vary by jurisdiction and occupancy type, so installations on exit doors should be reviewed by a licensed electrician, fire marshal, or security contractor familiar with local code rather than installed purely from a product manual. Power supply sizing matters too, since running two magnets off an undersized supply can lead to reduced holding force or unreliable operation; the power supply’s rated amperage should match or exceed the combined draw of both magnets.

Alternatives Worth Considering

Electrified Mortise or Cylindrical Locksets

Electric locksets built into the door itself, rather than mounted at the header, offer fail-secure operation in many configurations and a more conventional look, suiting applications where a visible exterior magnet isn’t desirable.

Electric Strikes

An electric strike replaces the standard door strike plate and works with a normal mechanical lockset, offering a lower-profile alternative to a header-mounted magnet, though it generally provides less raw holding force than a magnetic lock.

Standalone Keypad or Card-Access Deadbolts

For double doors where a full access-control system isn’t needed, standalone electronic deadbolts with keypad or card entry offer simpler installation without the header-mounted hardware or separate power supply a magnetic lock requires.

Planning the Installation

Before ordering a kit, it helps to measure the header depth and door width precisely, since bracket kits are generally designed around a specific range of frame dimensions and an undersized header can prevent a secure mount. It’s also worth mapping out where the power supply, request-to-exit sensor, and any fire alarm interface will be located, since running conduit or low-voltage wiring after drywall and finish work is complete is considerably more disruptive than planning the wiring path in advance. For any installation on a door along an egress path, getting a licensed electrician or fire-code-familiar contractor involved at the planning stage, rather than after installation, tends to avoid costly rework.

Frequently Asked Questions

How much holding force do I actually need for a double door?

Holding force needs depend on the door’s size, traffic level, and security requirements, with many commercial interior doors well served by 600 lb per leaf and higher-security or exterior doors often specified at 1,200 lb per leaf. A security consultant or access control integrator can assess the specific door and application if there’s uncertainty.

Magnetic locks can be used on fire exit doors in many jurisdictions, but only when properly integrated with a fire alarm release system, a request-to-exit sensor, and compliance with local fire and building code. This is a code compliance matter that should be confirmed with a local fire marshal or licensed contractor, not assumed from general product information.

What happens to a magnetic lock during a power outage?

Magnetic locks are fail-safe by design, meaning they release and unlock automatically when power is lost, which is one reason they’re commonly used on doors along egress paths. A backup battery can be added to the power supply if continuous locking during short outages is a priority, though this doesn’t override fire code release requirements.

Can I install a double-door magnetic lock myself?

Basic installation on a non-egress interior door is within reach for an experienced DIYer comfortable with the maker’s instructions and wiring a low-voltage power supply, but any installation involving a fire exit, alarm integration, or code compliance should involve a licensed electrician or security contractor. Incorrect installation on an egress door can create a genuine safety hazard.

Do both doors need their own separate magnet?

Yes, a true double-door magnetic lock kit includes two separate magnet-and-armature-plate assemblies, one per door leaf, since each leaf needs to be secured independently at its own meeting point with the frame or the other door. A single magnet cannot adequately secure both leaves of a double door.

Will a magnetic lock work with my existing access control system?

Most magnetic locks use standard low-voltage wiring (commonly 12V or 24V DC) compatible with common access control panels, card readers, and keypads, but voltage and current compatibility should be checked against the existing system’s specifications before purchase. An access control integrator can confirm compatibility for an existing installation.

B
Beckykinkead Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.